Spotting Scope Stand

Super Spotter Spotting Scope Stand

 

Here we have a pair of prototypes of the Super Spotter Spotting Scope Stand that I am currently developing specifically for the High Power Rifle Shooter, the Smallbore Shooter, and similar disiplines.
The stand on the right is the actual prototype that I used for over 5 years.  It has been dressed up with a few options that are available to increase the usefullness of the System.  It has an additional Scope Mounting Head and a pair of Stop Collars installed.  It also has a Custom Levelling System and steel weight installed on the bottom. 
This particular system went to a gentleman in Louisiana that works with junior shooters.  He wanted the ability to mount 2 scopes, one for the juniors and one for himself.  He also wanted the Levelling system and the extra weight.  Totally assembled, and without scopes, this system weighs 28 pounds.  The left  prototype, which is the Standard Model, without any of the extra options.  It weighs 8-1/2 pounds.

The basic system includes one fully adjustable billet Aluminum Scope Head Assembly with an O-Ring installed on the Scope Mounting Spool to resist gravity rotating the Scope Head when the deeply knurled Adjusting Knob is loosened, a billet Aluminum Base and Leg Assembly, and 2  Stainless Steel tubular masts that stand approx 65 inches tall.  The second generation System Legs have been machined from solid Aluminum bar stock into an I-beam configuration and have holes drilled for additional weight reduction.  They have also been lengthened by approx 3 inches to add to the stability with the larger scopes now on the market and in use by shooters.  Longer Spools are available to extend the scope farther from the mast.  F Class and Prone shooters have found this to be useful.

 This is one of the second generation Super Spotter Scope Stand assembled with the Scope Head and one mast section attached to the Base and Leg Assembly.  This is the configuration that I use when firing from the prone and sitting position.  The Scope Head can be had in Right Hand and Left Hand versions.  The Left Hand version is pictured.
This photo gives a better look at the Leveling option and the additional Weight that has been installed on this System.  The Levelling System is an option that can be retrofitted by the customer in a few minutes with a minimum of difficulty, factory retrofitted, or ordered completely installed from the factory.  The 2 Wing Headed Screws replace the Stainless Steel rolled pins that stop the Legs from rotating too far up.  To level the system, the Legs are swung into a downward position and the screws are threaded down a few turns, intentionally placing the System out of level.  After placing the System onto the ground, orient the System rotationally to get the best possible initial position.  Then, unscrew the Wing Headed Screws, lowering the Legs until the mast is in the vertical alignment that suits you.  It is easier to unscrew the Screws under load than it is to screw them in.
In this frame we have a Spotting Scope installed on a Right Handed Scope Head Assembly.  The deeply knurled Adjustment Knobs are clearly displayed.  Lightly snugging the horizontal Knob presses a Nylon insert against the Stainless Steel vertical Mast and maintains the height of the Scope Head Assembly.  A similar snugging of the angled Scope Elevation adjustment knob presses a Nylon insert against the Scope Mounting Spool and prevents vertical rotation of the Scope.  When the knobs are tightened sufficiently, the Scope Head will remain in position, but the shooter is able to adjust the horizontal sweep of the scope as well as the vertical tilt of the scope without loosening the Adjustment Knobs.
This frame shows the billet Aluminum Scope Mounting Spool with the O-Ring and the mounting screw.  I use Red Line grease on the O-Ring for reliable use in extreme hot and cold weather conditions.

Currently, we are supplying Stainless Steel screws and precision washers to adjust the length of protrusion of the screw that attaches your Scope to the Scope Mounting Spool.  If you do not wish to use the washers, it is a simple matter to file a few threads off the length of the screw to get an exact fit.
For no additional cost, we can supply the mounting screw as a stud that remains in the Spool.  Simply twist the scopes' threaded base onto the stud to mount it to the Spool.  This option is also available to current owners as an upgrade at no cost.  Return the Spool to Toolcraft and I will alter it as described above and return it to you in a week or less.
I am asking $290.00 for the Basic System, plus sales tax where applicable.
Shipping is additional at our actual cost.  Current UPS shipping to a US business address runs around $14-$22 depending on the options ordered.

The Basic Standard System includes:
1) 2 piece stainless steel mast, 1-1/4 diameter that finishes out at about 65 inches tall.
The center of the scope can be adjusted from 7 inches to 63 inches or more above the ground.
The masts may be fabricated in other custom lengths for no additional cost, as long as they are still approx 65 to 72 inches total.
2) A billet aluminum standard base that will also attach the Leveling system, the spike, or the bottom weight.
3) 3 billet aluminum folding legs with lightening holes and slots.  These legs have my cell phone number engraved in them.  No BS warranty applies.
4) One standard fully adjustable billet aluminum scope mounting head with 2 deeply knurled adjustment knobs and Scope Mounting Spool, w/Scope mounting Screw or Stud, with 1/4-20 threads.  Specify Stud or Screw Mount for Scope.
5) All stainless steel hardware.
6) A full, unlimited lifetime warranty on all parts, notwithstanding intentional abuse.

Assembled Basic System weight, without telescope……9 pounds Current Pricing  $290.00, U.S.

Please advise as to which type of scope attachment you want:
Standard is the Separate Stud, which uses a 3/16" Allen wrench to install the scope.

Optional is the Fixed Stud, which requires no tools to install.
Optional items:
1) 2 point Leveling system $55
2) Painted Steel, NOT stainless, weight for the base $35
3) Steel, NOT stainless, spike for driving into the ground $15
4) Stop Collar w/ Knurled Knob $35

5) Additional Scope head, with Knurled Knobs $85


6)      2-1/2" Extended Spool Upgrade/Exchange              $15




6a)    2-1/2" Extended Spool, Replacement                       $35


7)      Coach's Special, Dual Scope head, supports 2 scopes for stereo vision, like binoculars                          Still in the Design phase

8)      Top Ball handle with 3/16 diameter brass rod, used to drive stuck case from the chamber    $25


The standard length for the brass rod is 24 inches, but it can be up to 28 inches long for an additional $5

9)   Replacement for damaged hardware or O-Rings            No Charge

10) Anything else that you can imagine          Prices On Request

11) Advice on world problems                 No Charge

I am working on a design for a Bench Top adapter that clamps on the edge of a flat surface.  Please contact me for more information.

Any suggestions that could improve the usefullness of the Super Spotter Scope Stand System is greatly appreciated. 
And, we are offering a direct payment to anyone that is directly responsible for the sale of a System. 

We are talking CASH.  Not a coupon for goods, or anything silly like that. 
We are shooters, and appreciate a little help when we can get it.

Our email address is This e-mail address is being protected from spambots. You need JavaScript enabled to view it.
Many thanks for considering our products.

Thanks for your time.
Wayne McLeod
502-558-1043 Cell phone, actually answered by me.